Remainder of roll of 1/8 Fuel Pump Graphite Valve Packing Gas Engine Motor Hit Miss.
Home
› Tag Archives › motor
08May
Maytag & Small Engine Truck Cart Kit Briggs Hit Miss Axle Wheel Gas Motor
maytag
Comments Off
Brand new cart kit for small engines. Works great for Maytags! The long frame tank s-231 bolts right up to this neat little cart! Cast aluminum wheels measure 4 7/8″ diameter, allowing the 3/4″ axle to fit in there nice. The handle is just over 22 long. Wood skids and tank are NOT included. The 4 short carriage bolts and nuts for the long frame tank are included. We now make the axles with a lighter cored out bar.
04May
NELSON BROTHERS Hit Miss Gas Engine Piston Rod Cap 3K6 Steam Oiler 3 1/2 Motor
nelson
Comments Off
This is an original cast iron piston and rod with cap for a small Nelson Brothers hit and miss gas engine. The rod is part number 3K6 and the cap is K16. The assembly is in excellent condition with no cracks, breaks, or repairs of any kind except half of the rod bearing has been replaced with brass that worked well as this was in a running engine. The wrist pin has some mild wear The rings need to be replaced as they are all mismatched. The piston is 3 1/2 inches in diameter and the 3/4″ diameter wrist pin is 2 1/8″ on center from the top of the piston. Please measure your engine to be sure it works for your application. These original parts are exceedingly tough to find in the wild or even at swap meets! If you’ve been looking for one to complete a restoration or to replace your broken or repaired one here’s your chance. The pictures tell the story. I can be reached at 262 573 193 1 if you’d like to talk about it.
15Apr
Maytag & Small Engine Truck Cart Kit Briggs Hit Miss Axle Wheel Gas Motor
maytag
Comments Off
Brand new cart kit for small engines. Works great for Maytags! The long frame tank s-231 bolts right up to this neat little cart! Cast aluminum wheels measure 4 7/8″ diameter, allowing the 3/4″ axle to fit in there nice. The handle is just over 22 long. Wood skids and tank are NOT included. The 4 short carriage bolts and nuts for the long frame tank are included. We now make the axles with a lighter cored out bar.
21Mar
ALAMO ROCK ISLAND EMPIRE 303K18 Webster Magneto Ignitor Hit Miss Engine Motor
alamo
Comments Off
This is an extremely hard to find original Webster magneto ignitor bracket for a Alamo, Rock Island, Empire, Cockshutt, Moline, or other Alamo-built hit and miss gas engine. It should fit the 2 1/2 through 12hp engines but please measure your engine to be sure it will work for you. It is bracket number 303K18 and seems to be in good shape with and old solid repair as can be seen. It will need to be rebuilt or at least reassembled before it can be used. It seems to be very solid and should be a pretty straightforward project. It mounts with two holes 2 3/4 inches apart on center and the magneto mounts on a 2 x 2 inch hole pattern. The movable electrode moves nicely with very little wear and the pics show the condition of the points (one will need to be renewed). The advance/retard lever and roller move just as they should with only slight wear on the roller. After the addition of a few minor parts and some attention this should be a good, usable ignitor. If you need an Alamo/Rock Island ignitor bracket for any reason here is a pretty decent one. The pictures tell the story. It would also make a great spare on the shelf.
10Feb
GADE Hit Miss Gas Engine Governor WEIGHTS Steam Tractor Magneto Oiler Motor NICE
gade
Comments Off
This is a pair of original governor weights for a Gade hit and miss gas engine at least I’m pretty sure they’re Gade… If not please educate me! They are in great shape with no cracks, breaks, or repairs of any kind. There is one casting flaw that doesn’t affect anything. The governor weights are about 6 long and about 1 1/2 inches in diameter. They are about 4 1/4 inches deep. The leg that goes into the governor collar is about 2 1/8 inches long with a 5/16″ pivot hole and is about 5/8″ thick. The pictures tell the story. These original parts are quite tough to find so if you’ve been looking for some don’t miss your chance on these. They would also make great spares on the shelf.
05Feb
STARTING TORCH for HOT BULB SEMI DIESEL OIL ENGINE Old Hit and Miss Motor
starting
Comments Off
Here is an old starting torch for a hot bulb oil engine. The pump seems to be build some pressure but I would assume this torch would need to be gone through before use. The drip pan is loose on the stem, a set screw for that might be missing? Check out the pictures and see if you need it. For questions 419 789 1159. The tank is about 4-5/16 in diameter. About 12-5/8 in overall height. Missing knob for pump. Thanks for looking at this listing! If you want to check out my reputation and such please feel free to google search my name. My name and address is. 14316 State Route 281. If you can find a way to talk to me with your voice you will almost always get a quick response. If you message me please try not to sound like a caveman. I have terrible grammar myself so I understand but sometimes it is very difficult to comprehend what some people write. If I make a mistake on my measurements or you feel something is not as described please let me know and I will try to make it right. I think most all of my customers with a normal level of sanity are happy. I think most people would agree that I do an extremely good job of packing items so I guess it’s worth the wait. Check out my other items. Be sure to add me to your favorites list.
04Feb
DESJARDIN JULIEN Hit Miss Gas Engine Iron Starting Crank 2 Crankshaft Motor WOW
desjardin
Comments Off
This is a very nice original and very hard to find cast iron starting crank for a Desjardin orJulien hit and miss or throttle governed gas engine. It is in excellent condition with no cracks, breaks, or repairs of any kind. It fits on a 2 or 2 1/16″ inch crankshaft as it has a 2 1/8″ hole and will work to start many engines but it came from the factory with a Desjardin or Julien engine. The starting lug is in great shape. It is ready to go to work starting an engine! These cranks are quite tough to find in the wild or even at swap meets so if you need one to complete a restoration here it is. It would surely make starting your engine easier! The pictures tell the story. I can be reached at 262 573 193 1 if you’d like to talk about it.
